Completed planned maintenance inspection on outdoor air conditioning unit as part of recurring HVAC membership service. Accessed electrical compartment and inspected all major components including Genteq capacitor, contactor relay, wiring connections, and compressor motor. Unit interior showed significant accumulation of dirt, debris, cobwebs, and organic matter throughout compartment, indicating extended operation without recent maintenance. All electrical connections, capacitor, and contactor were visually inspected and found to be functional despite heavy soiling conditions.

Responded to no cooling complaint at commercial medical facility with complete loss of airflow to surgical area. Performed diagnostic evaluation on newer HVAC system and measured temperature readings at equipment using calibrated digital instrumentation. System found to be non-operational with no air delivery through ductwork and no tripped breakers reported.

Completed planned maintenance service on residential cooling system. Performed comprehensive inspection of outdoor condenser unit, verified proper electrical connections and capacitor operation, checked refrigerant levels, and confirmed all mechanical components functioning within normal parameters. Unit operating efficiently with no deficiencies noted at time of service.

# HVAC Membership - A/C Maintenance Completed Performed comprehensive planned maintenance service on residential air conditioning system. Conducted thorough inspection of outdoor condenser unit, including examination of electrical components, control boards, and wiring connections. Accessed internal control panel to verify proper operation of electronic controls and circuit boards. Inspected copper inductive coils, capacitors, and integrated circuits for signs of wear or damage. Verified all wire connections and harnesses were secure and properly routed. Checked condenser unit mounting on concrete pad and confirmed adequate drainage around equipment. Examined refrigerant line connections, electrical disconnect box, and PVC conduit installations. Documented equipment condition through photographic records. All components found operating within normal parameters. Unit ready for continued service.

Completed emergency plumbing repairs in women's restroom during scheduled water shut-off. Rebuilt urinal assembly and replaced defective shut-off valve for toilet fixture, restoring full functionality to both fixtures.

Responded to master bathroom toilet with continuous running condition and broken flush handle. Upon inspection, removed tank lid and identified worn flapper assembly and failed flush lever mechanism. Tank water showed significant mineral deposits and discoloration indicating age and hard water conditions. Replaced defective flush valve assembly including flapper seal and overflow tube. Installed new chrome flush handle and linkage assembly to restore proper manual operation. Adjusted fill valve and water level to manufacturer specifications. Tested flush cycle multiple times to verify proper tank refill, complete bowl evacuation, and elimination of continuous running. Confirmed all components sealed properly with no leaks detected. Toilet restored to full operational status.

Installed new A.O. Smith standard residential tanked water heater in accordance with quoted specifications. Unit was properly positioned, connected to existing water supply and discharge lines, and secured in utility area. Installation completed with all connections tested and system verified operational.

Completed comprehensive cooling season tune-up on 9-year-old residential air conditioning system. Performed visual inspection of outdoor condenser unit, noting significant accumulation of dirt, dust, and debris on condenser coils and protective wire guard. Opened electrical control panel and inspected internal components including dual-run capacitor, contactor relay, and associated wiring connections for proper operation and signs of wear. Cleaned condenser coils and removed organic debris from unit exterior to restore optimal airflow and heat transfer efficiency. Verified system operational status and confirmed unit cycling properly with no performance issues reported by customer.

Completed full HVAC system installation in new construction property, including ductwork rough-in throughout basement and main floor areas. Installed metal supply and return ducts with proper sizing and routing through framed walls and ceiling joists, ensuring adequate airflow distribution to all planned living spaces. System is ready for equipment connection and final commissioning once interior finishes are completed.

Completed planned air conditioning maintenance per membership agreement. Performed comprehensive system inspection of outdoor condensing unit, including visual examination of electrical components, capacitor, contactor assembly, and wiring connections. All electrical components found to be in proper working condition with secure wire connections and no signs of electrical failure. Noted standard wear consistent with normal operation. System operational and ready for cooling season.

Responded to no-cooling call on residential HVAC system approximately 10 years old. Upon arrival, confirmed system was clicking but failing to start with no airflow through vents and no tripped breakers. Performed diagnostic evaluation of electrical components at disconnect switch and main panel, inspected furnace unit and associated condensate lines, and examined all visible electrical connections and control circuits to identify failure point preventing compressor and blower operation.

Completed comprehensive summer tune-up and preventive maintenance on two residential air conditioning systems—one newly installed unit and one approximately ten-year-old system. Performed full inspection of both units including electrical component testing, capacitor verification, refrigerant level checks, condenser coil cleaning, and airflow assessment. All systems operating within manufacturer specifications with no deficiencies identified; both units cleared for continued service.

Responded to service call regarding sewer gas odor emanating from drainage system. Upon inspection of the utility area, identified a floor drain assembly with an improperly functioning or damaged trap primer device that was allowing sewer gases to escape into the building. The device in question appeared to be connected to the main drain line where it exits the building foundation. Documented existing conditions with photographs showing the drain configuration, PVC piping layout, and the suspected gas leak source. Advised customer on options for remediation, including potential replacement of the trap primer assembly or elimination of the device if not required by current plumbing code. Recommended follow-up evaluation to determine the most appropriate solution based on local code requirements and building usage.

Responded to service call for 10-year-old A.O. Smith tanked water heater producing insufficient hot water. Upon inspection, evaluated unit condition and verified operational status of all components including gas valve, burner assembly, thermostat, and pressure relief valve. Assessed water heater performance in basement utility area alongside existing HVAC system. Documented equipment configuration including piping connections, shut-off valves, and venting system. Customer advised of findings and unit status following diagnostic evaluation.

Completed scheduled cooling system maintenance on HVAC unit. Performed comprehensive inspection of electrical components including capacitor, contactor, and associated wiring connections. Verified all wire terminations were secure and properly connected to capacitor terminals and relay assembly. Inspected capacitor mounting and hardware for stability. Noted air filter size requirement of 16x25x4 (filters not included in service). All electrical components functioning within normal parameters. System operational upon completion of preventive maintenance.

Responded to a water leak at an irrigation fixture in the basement. Upon arrival, found active leaking around copper piping connections serving the irrigation system. The existing plumbing assembly showed significant age-related deterioration, including corrosion, mineral deposits, and oxidation on copper pipes and brass fittings. Inspected the affected area and identified the leak source at a compromised connection point near a shutoff valve. The surrounding wall exhibited water damage, cracking, and discoloration consistent with prolonged moisture exposure. Shut off water supply to the irrigation system to prevent further water intrusion. Disassembled the faulty connection and assessed the condition of the copper piping and fittings. Cleaned oxidized surfaces and removed corroded components. Replaced worn brass fittings and compromised sections of copper pipe as needed. Reinstalled a secure, watertight connection using proper soldering techniques and new compression fittings where

Completed pre-transfer utility inspection of residential HVAC system including air conditioning unit and furnace as requested for home sale. Performed comprehensive preventive tune-up on both systems, inspecting all major components, verifying proper operation, and documenting current condition. All findings recorded and inspection report prepared for real estate transaction documentation.

Performed planned maintenance inspection on HVAC system. Line temperatures at outdoor unit measured out of manufacturer specifications, preventing accurate refrigerant level assessment due to ambient conditions. Electrical readings verified within acceptable parameters per manufacturer guidelines. Follow-up visit required during warmer weather to complete refrigerant charge verification and determine if low refrigerant or coil cleaning is needed.

Completed follow-up maintenance on HVAC system after previous CWOW-Ptu service. Connected refrigerant manifold gauge set to system and verified operating pressures on both high and low sides to ensure proper refrigerant charge and system performance.

Completed planned air conditioning maintenance on outdoor condensing unit. Inspected electrical control panel components, contactor, and wiring connections. Applied capacitor start spray to relay and hard start components. Verified proper operation of condenser fan motor and grille assembly. Unit operating within normal parameters upon completion of scheduled maintenance service.